![pageSearch](/themes/hestia/images/page-search.webp)
Global High Purity Silicon Market Size and Forecast
Jun 16, 2023Rapid prototyping for high
Jun 08, 202346 Viral TikTok Products So Good, You’ll Be Tracking Delivery Until They Arrive
Jun 25, 202336 Things To Try If You're Craving Structure In Your Life
Jun 22, 2023The best embossing machines in August 2023
Jun 18, 2023Influence of diatomite and its base modifications on the self
![Feb 07, 2024](/themes/hestia/images/news-details-icon1.webp)
Scientific Reports volume 13, Article number: 13691 (2023) Cite this article
207 Accesses
Metrics details
The study examined how diatomite and its modifications affected the self-adhesive ability of silicone pressure-sensitive adhesives. To create adhesive composition for testing, fillers were added to a commercial silicone resin, which were then used to create new modified pressure-sensitive tapes. The resulting tapes were tested to determine their adhesion, tack, cohesion at room and elevated temperature, SAFT test (Shear Adhesive Failure Temperature), pot-life (viscosity) and shrinkage. The results obtained were compared with those of the unmodified tapes. The tests resulted in higher thermal resistance (225 °C) and lower shrinkage (0.1%). As a result, we can conclude that materials with thermal resistance with a slight decrease in other parameters were obtained.
Pressure-sensitive adhesives (PSA) are relatively new materials in the rail industry. As "eternally alive" viscoelastic materials, they exhibit permanent tacky at room temperature in solvent-free state,—tack when lightly pressed and no liquid to solid transformation. PSAs come in many different forms—double-sided adhesive tapes of various thicknesses with backing or functional foam cores, self-adhesive transfer tapes, single-sided tapes, and printing foils. In addition to their various forms, pressure sensitive adhesives have different chemical formulations and are suitable for a wide range of industrial applications. Among all pressure-sensitive adhesives, there are three most popular chemical formulations of which they are obtainable—acrylates, silicones and rubber1,2,3,4.
Silicone pressure sensitive adhesives are referred to as specialty materials. Since their introduction in 1960, silicone pressure sensitive adhesives (Si-PSAs) have found many applications, including tapes for bonding low surface energy materials, as well as in the electrical and electronics, medical and healthcare, and automotive industries. High flexibility of Si–O–Si connections in self-adhesive silicone adhesives, low intermolecular interaction, low surface tension, excellent thermal stability and UV transparency, excellent electrical properties, chemical resistance, and resistance to weather conditions make these adhesives relatively better than other conventional carbon-based PSAs. Si-PSA with methyl groups and phenyl are cross-linked at a temperature between 120 and 150 °C with organic peroxides. The adhesives are inert and very hydrophobic while maintaining good water vapor permeability. Since 2000, there has been an increase in interest in new silicone pressure-sensitive adhesives; especially as medical and industrial tapes. More and more attempts are made to modify adhesives in order to increase the desired properties (e.g. thermal resistance). Due to the lack of functional groups in the polymer and our own research experience, the finished silicone resins are physically modified by adding a filler to increase the thermal resistance of the adhesive5,6,7,8.
Silicone tapes are best known for their ability to stick to low surface energy materials and resistance to a very wide temperature range—from − 40 °C to over 250 °C. The basic characteristics of this group of self-adhesive materials are the ability to form adhesive bonds with silicone materials, relative resistance to mold and fungus (because silicone is "inorganic", which means that the skeleton is non-carbon, it is hypoallergenic in nature). Disadvantages are often mentioned the relatively low bond strength with non-silicone materials9,10,11.
Researchers are working to significantly increase the potential of zeolite raw material, such as diatomite, through the use of various modification methods. Modification is of great interest mainly because of not only the significant occurrence and properties of such materials, but also the optimized yield and low cost. Modified zeolites represent versatile prospects for various applications. Modification of zeolites is most often used to increase their ion-exchange capacity, to increase their capacity and to obtain a more selective material12.
Diatomite is a material of sedimentary origin. The diatomite deposits consist mainly of an accumulation of skeletons formed by the formation of diatoms. The skeletons are amorphous hydrated or opalescent silica, but sometimes consist partly of alumina. Diatomite besides diatom shells usually contains other sediments such as clay and fine sand13.
Wang, Yang et al. modified the diatomite by easy alkaline treatment. The crude diatomite was dispersed in NaOH solution at 90 °C while stirring for 2 h. After separation, the modified diatomite was washed several times with water and anhydrous ethanol until a pH value close to neutral was obtained14.
Boriskov et al. modified the diatomite with 1N hydrochloric acid, and by using a 1N NaOH solution for 1 h was carried out. The samples were then washed repeatedly with distilled water, neutralized to pH 7. The next step was drying at room temperature to an air-dry state. Thermal activation was carried out by annealing the native, pre-washed and sieved diatomite in a muffle furnace for 3 h at 440–460°C14.
Xu et al. modified diatomite by KOH through mixed them in a round-bottom flask with a rotor at 60 °C for 24 h, with a KOH/diatomite mass ratio of 1:6 to 1:1. A magnetic heating stirrer was used to impregnate the dry mixture . The sample was then calcined in a muffle furnace at 300 °C to 700 °C for 4 h15,16.
Diatomite, sodium hydroxide and distilled water were mixed in a three-necked flask17. The flasks were sealed with stoppers to prevent evaporation of the solution. The flask was immersed in a water bath at a fixed temperature and the system was kept stirring for 3 h. The resulting mixture was filtered on filter paper and then washed with distilled water until no sodium ions could be detected in the solution.
The goal of work was modification of self-adhesive silicone resins with the fillers to obtained new silicone pressure-sensitive adhesives composition with increased thermal resistance. Fillers assist in the transfer of temperature through the material, thus increasing thermal resistance. Self-adhesive tapes were obtained from the prepared compositions. Diatomite was selected as a filler improving thermal resistance; the filler was also alkali-etched.
The following materials were used to create this paper:
Silicone adhesive from Dow Corning (USA)—resin DOWSIL™ 7358 (Q2-7358).
Cross-linking compound was dichlorobenzoyl peroxide—DClBPO (Gelest – USA).
Solvent was toluene from Carl Roth (Germany).
Diatomite (diatomaceous earth) from Nanga (Poland) was used as a filler.
According to the manufacturer's assurances, the particle size of diatomaceous earth (diatomite) is to 10 µm. Based on the manufacturer's tests, the chemical composition of the filler was assumed as: SiO2 93.0%; Al2O3 2.0%; Fe2O3 1.0%; CaO 0.3%; Na2O + K2O 2.5%; MgO 0.5%; TiO2 0.2%; P2O5 0.1%.
Dowsil 7258 is a solvent-base silicone pressure-sensitive adhesive dispersion of polydimethylsiloxane gum and resin (52–58%) in toluene/xylene.
Diatomite samples were modified with NaOH and KOH solutions of different concentrations of 0.1 M, 0.5 M and 1 M for 6 h at 60 °C. For modification, 100 ml of the corresponding solution per 10 g of sample was used. The whole was placed in an ultrasonic bath. The resulting samples were centrifuged (7000 rpm), washed with deionized water to pH 7 of filtrate and dried at 85 °C for 24 h.
To prepare one-side self-adhesive tape the commercial resin was medicated by using 1.5 parts crosslinking agent wt. for 100 parts wt. resin. Then 0.1; 0.5, 1,0 or 3,0 wt% filler was added to a modified resin and mixed until a homogeneous composition was obtained. That obtained compositions were coated onto a 50 μm thick polyester film using a semi-automatic PSAT coater. The composition coated in this way was introduced into a Binder dryer (Binder GmbH, Germany) at a temperature of 110 °C for 10 min for solvent evaporation and thermal cross-linking. That obtained adhesives film with a weight of 45 g/m2 was secured with another layer of polyester film.
The FTIR spectra were made using a Nicolet 380 spectrometer from Thermo Electron Corporation (Waltham, MA, USA). The study used the ATR attachment with a diamond crystal. The measurement range was from 4000–400 cm−1 at a resolution of 4 cm−1.
The XRD of the modified diatomite’s was obtained by an Empyrean PANalytical X-ray diffractometer (Malvern, UK) with a Cu lamp used as the radiation source in the 2θ 10–100° range with a step size of 0.026.
The pot life is defined as the period of time during which a given composition can be coated without problems. After a long storage time of the composition (mainly after the addition of the cross-linker), the viscosity of the composition increases until the so-called gel point18. The tests were performed with a Brookfield viscometer at room temperature at intervals, immediately after mixing and after 1, 2, 3, 5, 7 days, respectively. Pot-life was determined using a DV-II Pro Extra viscometer (Brookfield, New York, NY, USA).
Using a solvent analyzer (Radwag MAX 60/NP, Radom, Poland) was measured the solid’s content of the starting adhesive. The measurement was carried out in aluminum crucibles at 140 °C for 40 min. The basis weight of the adhesive film was measured using a round punch with area of 10 cm2 (Karl Schröder KG, Weinheim, Germany).
Adhesion is a phenomenon of the interaction of particles, atoms and ions, adjacent surfaces. The measure of adhesion is the work per unit area that has to be done in order to release adhesively sticked materials19. The peel adhesion test was carried out in accordance with the AFERA 4001 test method on the Zwick-Z010 testing machine (Zwick/Roell, Germany). After removing the release liner, the foil was stuck to a steel plate using a 2 kg roller. The sample was left for 20 min. The peel adhesion was measured for each test piece at an angle of 180°. The result of the measurement is the average of the five measurements20,21.
Cohesion is a type of intermolecular interaction due to which the molecules of a given substance are kept in close proximity. The measure of cohesion is the work required to separate a certain body into its parts divided by the area resulting from the separation. Cohesion depends, inter alia, on the state of aggregation, the microstructure of the material, and the size of interactions between molecules. Cohesion was measured according to the AFERA 4012 standard at 20 and 70 °C. According to this method, a part of the strip measuring 2.5 cm × 2.5 cm is stuck to the steel plate, and the other end of the strip is loaded with a weight of 1 kg. The test measures the time that elapsed until the adhesive film separates from the tile22.
The ability to stick two surfaces quickly and reliably is a key performance requirement in many pressure sensitive adhesive products, especially adhesive tapes and labels. The key property for successful bonding is the tack or "stickiness" of the adhesive. The tack test is performed in accordance with the AFERA 4015 standard. The value of the tack is defined as the force required to separate, at a predetermined speed, the loop which touches an area with a predetermined surface by means of an adhesive23,24.
The samples were prepared according to the procedure described for the cohesion tests. A mass of 1 kg was suspended at each end of the sample and placed in the oven. The temperature was increased from 22 to 217 °C at a heating rate of 1 °C/min. The damage temperature was given along with the nature of the adhesive damage. Tests were carried out on 4 samples for each formulation to determine the mean temperature resistance, and the standard deviation was used as the error23.
Shrinkage was measured using the cross method, where the PVC film is coated with a thin layer of adhesive, cross-linked and then sticked to a metal plate. Two 90° incisions are made. Measurements are made by measuring the width of the cuts at various intervals keeping the test temperature at 70 °C. Shrinkage is a percentage of the ratios of the cut widths. Shrinkage greater than 0.5% is not allowed20,25.
An adhesive composition with good functional properties was selected for modification with fillers. The results for the pressure-sensitive adhesive without modification are presented in Table 1. However, self-adhesive tapes without modification show a low temperature value in the SAFT test, which limits the range of applications of such tapes. At the same time, they are characterized by good cohesion at room temperature and elevated temperature. Moreover, the adhesion and tack values are good. This leads to the conclusion that the planned physical modifications with diatomite based fillers can have a positive effect on the Si-PSA proportions. It was expected that this addition would improve the thermal properties of self-adhesive tapes while maintaining the performance properties, such as adhesion or cohesion, at the same level as unmodified tapes. The modified adhesive had a viscosity equal to 16.7 Pa s and contained 57.6% of solids (measured thermogravimetrically). Only the crosslinker (thermal)—1.5 pph of dibenzoyl peroxide was added to it and diluted with toluene (to 55% solids).
Figure 1 FTIR spectra of the raw diatomite and the modified diatomite’s are shown. The peaks at 3421, 1631 cm−1 and 960 cm−1, which are observed in all seven samples, are typically associated with stretching vibrations of the hydroxyl (–OH) groups on the surface of the samples. With increasing concentrations of NaOH and KOH the intensity of the peak at 960 cm1 increases, which is confirmed by the increase in the number of OH groups. The peaks at 1054, 796 and 451 cm-1 are attributed to asymmetric stretching, symmetric stretching and bending modes of the Si–O–Si bonds in the diatomite26.
FTIR spectra of the raw diatomite and the modified diatomite’s NaOH and KOH solutions.
Figure 2 shows the XRD patterns of the raw diatomite and the diatomite’s modified with NaOH and KOH solutions. A broad peak at about 22.5° associated with the amorphous structure of SiO2 is observed. These are typical non-crystalline diffraction peaks. The absence of other reflections indicates a very high purity of diatomite.
XRD of the raw diatomite and the diatomite’s modified with NaOH and KOH solutions.
Figures 3a and b show the effect of the addition of diatomite-based fillers on the adhesion of the adhesive film. The diagrams respectively show tapes modified with fillers etched with sodium and potassium base of different concentration in order to change the ratio of silicon to the rest of the filler. A small addition of the filler (0.1 or 0.5% by weight) increased the value of adhesion compared to the composition withoutthe filler, while with a large addition, its decrease was noted. It is caused most similarly by the effect of the desirable and more compact structure caused by the introduction of small amounts of filler, and when the amount is increased, it causes a shift of the cohesive-adhesive balance towards cohesion27,28. In each case of filler modification, an increase in adhesion value was observed compared to films modified with unmodified diatomaceous earth. The greatest increase was recorded for small fillings (0.1 or 0.5% by weight) with fillers modified with 0.1 and 0.5 molar solutions. Out of the samples modified with an additive 0.5 wt% filler the highest value of peel adhesivon obtained for diatomite modified 0.1 molar NaOH. − 15.8 N/25 mm. It was also noticed that even a small addition of a filler modified 1 molar base allows to achieve much higher adhesion than in the case of a use filler modified 0.1 molar base, where for the KOH-modified diatomite higher values were obtained by the system etched with a 0.5 molar base solution.
Effect of diatomite addition on the peel adhesion of silicone pressure-sensitive adhesives: (a) diatomite modified byNaOH; (b) diatomite modified byKOH.
The tack of the modified adhesive films maintained a similar tendency as in the case of its adhesion (Fig. 4). A small addition − 0.1% by weight of the filler increased the value of tack compared to the composition with the filler. Already for the addition of 1.0 wt. fillers, a reduction in tack value close to or lower than the value achieved by the unmodified adhesive film has been reported. This relationship is related in part to the shift of the cohesive-adhesive balance towards cohesion and the arrangement of the adhesive film. A systematic decrease in the value of stickiness after its increase may also be caused by the appearance of glue blockages (particles of the filler not covered with the adhesive layer) on the surface of the adhesive material, which will automatically lower the value of tack27,28,29.
Efect of diatomite addition on the tack of silicone pressure-sensitive adhesives: (a) diatomite modified byNaOH; (b) diatomite modified byKOH.
No effect of the filler addition or its basic modification on the cohesive properties of the adhesive composition was observed. In the case of both NaOH and KOH, all samples tested showed high cohesive resistance of over 72 h at room and elevated temperatures.. The test results are presented in Figs. 5 and 6. This effect confirms the good compatibility of the fillers with the silicone resin; and in combination with the results of adhesion and tackiness, a better arrangement of polymer chains and a more compact structure of the adhesive film caused by the addition of the filler are confirmed27,28.
Efect of diatomite addition on the cohesion of silicone pressure-sensitive adhesives measurement at room temperature: (a) diatomite modified byNaOH; (b) diatomite modified byKOH.
Efect of diatomite addition on the cohesion of silicone pressure-sensitive adhesives measurement at 70 °C: (a) diatomite modified byNaOH; (b) diatomite modified byKOH.
The obtained new adhesive tapes were tested by means of the SAFT test in order to determine their thermal resistance and to compare them to unmodified tapes; the results are shown in Fig. 7. The addition of fillers increased the thermal resistance of the tested adhesive compositions, along with the increase of the additive, the temperature resistance increased each time, reaching the test limit of 225 °C in the region of 0.5 to 1.0% by weight of the additive. For samples etched with NaOH and KOH bases, this value was already achieved at 0.1 weight percent. At 3% by weight of the additive, a decrease in the maximum operating temperature was noted, but not below the value of the samples without fillers. Etching samples with bases improves their compatibility with silicone resin and increases its thermal resistance, it may be related to the increase in silicon mass in the pickled fillers compared to the rest of the filler28,29,30. Fillers assist in the transfer of temperature through the material, thus increasing thermal resistance31.
Efect of diatomite addition on the thermal resistance in SAFT test of silicone pressure-sensitive adhesives: (a) diatomite modified byNaOH; (b) diatomite modified byKOH.
In each test case, the viscosity of the samples increased rapidly to form a gel—the samples doubled their viscosity or reached the maximum viscosity allowing the use of the adhesive composition for the 74 Pa s coating; in the first case, the samples had settled to the edge of the gel after about 7 days, while in the second case, the maximum was reached by samples with the addition of 3% by weight of alkali-modified filler, regardless of the molar concentration used for its modification. Compared to pure adhesive compositions, the addition of diatomaceous earth slightly affected viscosity, even at the highest additive level tested.. In addition, studies have shown that when modifying by using base, the distances between the individual curves in the graph expand with the amount of filler added. A slight addition of 0.1 weight percent of the modified filler increases the viscosity twice as compared to the viscosity of the composition with the addition of the unmodified filler. The difference between the addition of the modified filler 0.1, 0.5 and 1.0 is relatively close and oscillates around a twofold increase in viscosity, while with the addition of 3% by weight of the filler, about fourfold increase in viscosity was noted—Fig. 8. There were no particular differences after the modification with the base of NaOH and KOH. A key role is played by OH groups, which cause the carbon atoms of the benzene group to attract hydroxyl protons through OH-π interactions. Increased content of OH groups in the modified filler significantly increases viscosity32.
Efect of diatomite addition on the viscosity of silicone pressure-sensitive adhesives: (a) diatomite; (b) diatomite modified by 0.1 NaOH; (c) diatomite modified by 0.5 NaOH; (d) diatomite modified by 1.0 NaOH; (e) diatomite modified by0.1 KOH; (f) diatomite modified by 0.5 KOH; (g) diatomite modified by 1.0 KOH.
Figure 9 shows the effect of diatomite and its alkaline modifications on the shrinkage value of pressure-sensitive silicone adhesives. The incorporation of a filler into the composition led to a dramatic reduction in the shrinkage value compared to an adhesive composition without fillers. The lower the addition of the filler, the smaller the skin of the tested samples was, the best results were obtained for fillings from 0.1 to 0.5% by weight. Most likely, this was due to a better alignment of polymer chains and a more compact structure, which improved the shrinkage of the adhesive film28,33. Modification of diatomite with bases allowed to obtain lower shrinkage values for each degree of filling of the adhesive compositions. The research showed that the materials treated with the highest molar concentrations gave the best results. The most probable reduction in shrinkage in this case was due to the increase in the proportion of silicon in the filler mass and the possible changes in its structure caused by the action of bases29.
Efect of diatomite addition on the shrinkage of silicone pressure-sensitive adhesives: (a) diatomite modified by 0.1 NaOH; (b) diatomite modified by 0.5 NaOH; (c) diatomite modified by 1.0 NaOH; (d) diatomite modified by 0.1 KOH; (e) diatomite modyficated 0.5 KOH; (f) diatomite modified by 1.0 KOH, (g) diatomite.
Research has resulted in self-adhesive tapes with improved properties compared to the starting adhesive. A very large increase was observed in the case of thermal resistance—most of the samples reached the maximum value: 225 °C. Shrinkage results were also exceptional, with virtually every filler addition resulting in a reduction in shrinkage. In each tested case, a rapid increase in the viscosity of the samples to the form of a gel was noted, so the obtained compositions are not suitable for storage and must be coated immediately after being tapped. In addition, the tapes retained good sub-aquatic properties such as adhesion, cohesion and tack, which makes them usable.
By introducing diatomaceous earth into the polymer matrix, new self-adhesive tapes with increased thermal resistance were obtained. Additional modification of diatomite with different bases and their introduction into Si-PSA resulted in further expansion of the possibilities of obtaining tapes with specific limiting parameters, thanks to which several self-adhesive products with specific thermal resistances can be prepared from the obtained results.
Wherever resistance to high temperatures and material expansion are required, the materials obtained can certainly be used. The main industry that could be the recipient of the products described in the paper is heating plants, where the tapes could be used to seal pipes.. In addition, these materials can be an interesting alternative to quick connectors used in the automotive industry, especially since they can be used in engines.
The datasets used and/or analyzed during the current study available from the corresponding author on reasonable request.
Czech, Z. et al. Novel photoreactive pressure-sensitive adhesives (PSA) based on acrylics containing additionable photoinitiators. Materials (Basel) 13, 1–12. https://doi.org/10.3390/ma13225151 (2020).
Article CAS Google Scholar
Tobing, S. D. & Klein, A. Molecular parameters and their relation to the adhesive performance of emulsion acrylic pressure-sensitive adhesives II Effect of crosslinking. J. Appl. Polym. Sci. 79, 2558–2564. https://doi.org/10.1002/10974628(20010401)79:14%3c2558::AIDAPP1065%3e3.0.CO;2-Yopen_in_newISSN002 (2001).
3.0.CO;2-Yopen_in_newISSN002" data-track-action="article reference" href="https://doi.org/10.1002%2F10974628%2820010401%2979%3A14%3C2558%3A%3AAIDAPP1065%3E3.0.CO%3B2-Yopen_in_newISSN002" aria-label="Article reference 2" data-doi="10.1002/10974628(20010401)79:143.0.CO;2-Yopen_in_newISSN002">Article CAS Google Scholar
Czech, Z. & Wesolowska, M. Development of solvent-free acrylic pressure-sensitive adhesives. Eur. Polym. J. 43, 3604–3612. https://doi.org/10.1016/j.eurpolymj.2007.05.003 (2007).
Article CAS Google Scholar
Deng, X. Progress on rubber-based pressure-sensitive adhesives. J. Adhes. 94, 77–96. https://doi.org/10.1080/00218464.2016.1249573 (2018).
Article CAS Google Scholar
Meurer, M., Dresbach, C. & Möginger, B. Rate dependent tack behavior of silicone-based pressure sensitive adhesives for transdermal therapeutic systems. https://doi.org/10.21203/rs.3.rs-3010924/v1 (2023)
Pradeep, S. V., Kandasubramanian, B. & Sidharth, S. A review on recent trends in bio-based pressure sensitive adhesives. J. Adhes. https://doi.org/10.1080/00218464.2023.2176761 (2023).
Article Google Scholar
Park, H. W., Seo, H. S., Kwon, K., Lee, J. H. & Shin, S. Enhanced heat resistance of acrylic pressure-sensitive adhesive by incorporating silicone blocks using silicone-based macro-azo-initiator. Polymers (Basel) 12, 1–15. https://doi.org/10.3390/polym12102410 (2020).
Article CAS Google Scholar
Ho, K. Y. & Dodou, K. Rheological studies on pressure-sensitive silicone adhesives and drug-in-adhesive layers as a means to characterise adhesive performance. Int. J. Pharm. 333, 24–33. https://doi.org/10.1016/j.ijpharm.2006.09.043 (2007).
Article CAS PubMed Google Scholar
Abenghal, L., Lamoudan, H. & Brouillette, F. Alkylated phosphorylated fibers: A new substitute for silicone in release paper manufacturing. BioResources 18, 2172–2186. https://doi.org/10.15376/biores.18.1.2172-2186 (2023).
Article CAS Google Scholar
Tolia, G. & Kevin Li, S. Study of drug release and tablet characteristics of silicone adhesive matrix tablets. Eur. J. Pharm. Biopharm. 82, 518–525. https://doi.org/10.1016/j.ejpb.2012.07.006 (2012).
Article CAS PubMed Google Scholar
Lin, S. B., Durfee, L. D., Ekeland, R. A., McVie, J. & Schalau, G. K. Recent advances in silicone pressure-sensitive adhesives. J. Adhes. Sci. Technol. 21, 605–623. https://doi.org/10.1163/156856107781192274 (2007).
Article CAS Google Scholar
Shi, J. et al. Preparation and application of modified zeolites as adsorbents in wastewater treatment. Water Sci. Technol. 2017, 621–635. https://doi.org/10.2166/wst.2018.249 (2018).
Article PubMed Google Scholar
Chaisena, A. & Rangsriwatananon, K. Synthesis of sodium zeolites from natural and modified diatomite. Mater. Lett. 59, 1474–1479. https://doi.org/10.1016/j.matlet.2004.10.073 (2005).
Article CAS Google Scholar
Wang, T. et al. A general route to modify diatomite with niobates for versatile applications of heavy metal removal. RSC Adv. 9, 3816–3827. https://doi.org/10.1039/C8RA10186H (2019).
Article CAS PubMed PubMed Central ADS Google Scholar
Boriskov, D., Efremova, S., Komarova, N., Tikhomirova, E. & Bodrov, A. Applicability of the modified diatomite for treatment of wastewater containing heavy metals. E3S Web Conf. 247, 01052. https://doi.org/10.1051/e3sconf/202124701052 (2021).
Article CAS Google Scholar
Xu, Q. et al. Diatomite stabilized KOH: An efficient heterogeneous catalyst for cyclopentanone self-condensation. ChemCatChem 13, 916–923. https://doi.org/10.1002/cctc.202001538 (2021).
Article CAS Google Scholar
Du, G., Lü, G. & He, X. Apparent dissolution kinetics of diatomite in alkaline solution. Chin. J. Chem. Eng. 21, 736–741. https://doi.org/10.1016/S1004-9541(13)60533- (2013).
Article CAS Google Scholar
Czech, Z. Crosslinkable propyleneimine pressure-sensitive adhesive acrylates and their pot life. Polym. Adv. Technol. 15, 539–543. https://doi.org/10.1002/pat.470 (2004).
Article CAS Google Scholar
Righetti, M. & Lucarelli, C. May the shields theory be extended to cohesive and adhesive benthic sediments?. J. Geophys. Res. 112, C05039. https://doi.org/10.1029/2006JC003669 (2007).
Article CAS ADS Google Scholar
Mozelewska, K. & Antosik, A. K. Influence of silicone additives on the properties of pressure-sensitive adhesives. Materials (Basel) 15, 5713. https://doi.org/10.3390/ma15165713 (2022).
Article CAS PubMed ADS Google Scholar
Abu Bakar, R., Li, Y., Hewitson, O. P., Roth, P. J. & Keddie, J. L. Azide photochemistry in acrylic copolymers for ultraviolet cross-linkable pressure-sensitive adhesives: optimization, debonding-on-demand, and chemical modification. ACS Appl. Mater. Interfaces 14, 30216–30227. https://doi.org/10.1021/acsami.2c07385 (2022).
Article CAS PubMed PubMed Central Google Scholar
Kim, H. J. et al. Study of UV-initiated polymerization and UV crosslinking of acrylic monomers mixture for the production of solvent-free pressure-sensitive adhesive films. Polym. Test. 105, 107424. https://doi.org/10.1016/j.polymertesting.2021.107424 (2022).
Article CAS Google Scholar
Chen, H., Ma, X., Xu, D., Chen, G. & He, L. Investigation of the tack force of poultices using the probe tack test. J. Adhes. Sci. Technol. https://doi.org/10.1080/01694243.2022.2082745 (2022).
Article Google Scholar
Ma, Y. et al. Research advances of vegetable oil based pressure sensitive adhesives. Green Mater. https://doi.org/10.1680/jgrma.22.00061 (2022).
Article Google Scholar
Wirries, J. & Ruetters, M. Methods for shrinkage measurement considering stress development of curing structural adhesives. Proc. Inst. Mech. Eng. Part. D J Automob. Eng. https://doi.org/10.1177/09544070221103676 (2022).
Article Google Scholar
Li, Z. et al. Synthesis of a MnO2/Fe3O4/diatomite nanocomposite as an efficient heterogeneous Fenton-like catalyst for methylene blue degradation. Beilstein J. Nanotechnol. 9, 1940–1950. https://doi.org/10.3762/bjnano.9.185 (2018).
Article CAS PubMed PubMed Central Google Scholar
Antosik, A. K., Musik, M., Mozelewska, K. & Miądlicki, P. Influence of cleaned granite dust on the properties of silicone pressure-sensitive adhesives. J. Anal. Pharm. Res. 11, 27–30. https://doi.org/10.15406/japlr.2022.11.00398 (2022).
Article Google Scholar
Antosik, A. K., Mozelewska, K., Piątek-Hnat, M., Czech, Z. & Bartkowiak, M. Silicone pressure-sensitive adhesives with increased thermal resistance. J. Therm. Anal. Calorim. 147, 7719–7727. https://doi.org/10.1007/s10973-021-11048-y (2022).
Article CAS Google Scholar
Antosik, A. K. & Mozelewska, K. Influence of nanoclay on the thermo-mechanical properties of silicone pressure-sensitive adhesives. Mater. (Basel) 15, 7460. https://doi.org/10.3390/ma15217460 (2022).
Article CAS ADS Google Scholar
Antosik, A. K., Makuch, E. & Gziut, K. Influence of modified attapulgite on silicone pressure-sensitive adhesives properties. J. Polym. Res. 29, 135. https://doi.org/10.1007/s10965-022-02981-z (2022).
Article CAS Google Scholar
Fu, Y.-X., He, Z.-X., Mo, D.-C. & Lu, S.-S. Thermal conductivity enhancement with different fillers for epoxy resin adhesives. Appl. Therm. Eng. 66, 493–498. https://doi.org/10.1016/j.applthermaleng.2014.02.044 (2014).
Article CAS Google Scholar
Nakamura, S., Tsuji, Y. & Yoshizawa, K. Role of hydrogen-bonding and OH−π interactions in the adhesion of epoxy resin on hydrophilic surfaces. ACS Omega 5, 26211–26219. https://doi.org/10.1021/acsomega.0c03798 (2020).
Article CAS PubMed PubMed Central Google Scholar
Antosik, A. K., Mozelewska, K., Czech, Z. & Piątek-Hnat, M. Influence of montmorillonite on the properties of silicone pressure-sensitive adhesives: Preparation of a double-sided tape based on the best composition. SILICON 12, 1887–1893. https://doi.org/10.1007/s12633-019-00295-2 (2020).
Article CAS Google Scholar
Download references
This research was funded by the National Center for Research and Development (NCBiR) as part of the LIDER initiative. Project number LIDER/9/0028/L-11/19/NCBR/2020.
Faculty of Chemical Technology and Engineering, Department of Chemical Organic Technology and Polymeric Materials, West Pomeranian University of Technology, Szczecin, Pulaskiego 10, 70-322, Szczecin, Poland
Adrian Krzysztof Antosik, Karolina Mozelewska & Marlena Musik
Faculty of Chemical Technology and Engineering, Engineering of Catalytic and Sorbent Materials Department, West Pomeranian University of Technology in Szczecin, Piastów Ave. 42, 71-065, Szczecin, Poland
Piotr Miądlicki
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
Conceptualization. A.K.A., M.M., P.M., K.M.; methodology. A.K.A., M.M., P.M.K.M.; validation. A.K.A.; formal analysis. A.K.A., K.M., P.M.; investigation. A.K.A., M.M., P.M., K.M.; data curation. A.K.A., M.M.; writing—original draft preparation. A.K.A., M.M., P.M., K.M.; writing—review and editing. A.K.A., M.M., P.M., K.M..; supervision. A.K.A.; project administration. A.K.A.; funding acquisition. A.K.A. All authors reviewed the manuscript.
Correspondence to Adrian Krzysztof Antosik.
The authors declare no competing interests.
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
Reprints and Permissions
Antosik, A.K., Mozelewska, K., Musik, M. et al. Influence of diatomite and its base modifications on the self-adhesive properties of silicone pressure-sensitive adhesives. Sci Rep 13, 13691 (2023). https://doi.org/10.1038/s41598-023-40958-0
Download citation
Received: 07 February 2023
Accepted: 19 August 2023
Published: 22 August 2023
DOI: https://doi.org/10.1038/s41598-023-40958-0
Anyone you share the following link with will be able to read this content:
Sorry, a shareable link is not currently available for this article.
Provided by the Springer Nature SharedIt content-sharing initiative
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.